Reloading Tools

FEATURES
-.309diameter
-170 grain
-Round nose bullet
-Suitable for cartridges like .30 caliber rifle
-Handles included

FEATURES
-Shell Holder #4
-Built from hardened steel
-Designed to properly align the case with the reloading die in single-stage & turret presses
-Sized to fit specific case heads & capture 0.125" of the case head for proper SAAMI head spacing

FEATURES
-Caliber: .500 Cal
-This collet is designed to be used with the RCBS® Standard Bullet puller to remove bullets from a wide
range of cases

FEATURES
-Taper Crimp Die for .44 Special, .44 Magnum
-Overcomes crimp problems caused by poor design
-Offers little or no advantage when used with 1986 or newer Lee dies as the
crimp angle is already a modified taper crimp

FEATURES
-28 gauge
-3/4 oz. charge bar
-Bushings: 14, 16, 21
-Works on six shells at once
-Fully automatic primer feed
-Auto-cycle charging
-Three-stage crimp
-"Power Ring" resizer
-Automatic indexing
-Finished-shell ejection
-Auto-Dex™ automatically moves the shells through each reloading stage by
simply returning the handle to the top of its stroke

FEATURES
-Caliber: .44-40 Winchester
-The 3-Die Roll Crimp Set is for loading straight-wall cartridges
-Its steel Sizer Die sized the case & de-primes
-Note: Cases must be lubricated
-The Expander Die expands the case to the proper diameter to accept the bullet, & it imparts
case mouth flare/bell for bullet feeding
-The Seater Die seats the bullet & roll crimps

FEATURES
-Caliber: .22 Hornet
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

FEATURES
-Complete reloading system for.243 Winchester
-Does not include rubber mallet

FEATURES
-Removes residue in primer pockets with a couple of twists
-Stainless bristles & interchangeable mounts

FEATURES:
-Dry media can be used in both Sidewinder & Vibratory Case Cleaners
-Ground to a 12/12 sieve size
-Polish comes individually packed so you can choose various amounts of media to mix

FEATURES
-Caliber: .30-40 Krag
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

FEATURES
-Factory crimp die for .204 Ruger
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation

FEATURES
-Factory crimp die for .44/40 Winchester
-Crimps bullet in place more firmly than any other tool
-A firm crimp improves accuracy
-Higher start pressure insures a more uniform pressure curve & less velocity variation

FEATURES
-12 gauge
-1 1/8 oz. charge bar
-Bushings: 29, 30, 32
-Works on six shells at once
-Fully automatic primer feed
-Auto-cycle charging
-Three-stage crimp
-"Power Ring" resizer
-Automatic indexing
-Finished-shell ejection
-Auto-Dex™ automatically moves the shells through each reloading stage by
simply returning the handle to the top of its stroke

FEATURES
-For7MMRemingtonMagnum
-Check the quality and consistency of both reloaded rounds and purchased ammunition
-Allow a reloader to quickly confirm that their ammunition will fit in their chamber
-Machined from solid blocks of 6061 T6 aircraft grade aluminum
-Cut with custom tooling to SAAMI minimum chamber dimensions
-Bright orange anodizing makes them easy to find on your reloading bench

FEATURES
- Caliber: .223 Remington/5.56mm
- Feature a Small Base Sizer Die designed for semi-automatic firearms, and a Taper Crimp Seater Die
-The Small Base Sizer guarantees the cartridge will rechamber in AR-platform weapons
- 2 dies/set

FEATURES
-Caliber: .257 Weatherby Magnum
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

FEATURES
-Caliber: .300 Remington Ultra Magnum
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

FEATURES
-Caliber: 6.5 Creedmoor
-This two-die set is intended for reloading bottleneck cases, & consists of a Full-Length Sizer Die
with an Expander-Decapping Unit, & a Seater Die with Bullet Seater Plug.
-The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions
-It sizes the outside of the case, de-primes & expands the neck to accept the bullet
-The die vents to prevent case damage caused by trapped air & for excessive lubricant
-Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing
-Then included Seater Die has a built-in roll crimper to secure the bullet at the same time as it's seated

FEATURES
-Shell Holder #44
-Built from hardened steel
-Designed to properly align the case with the reloading die in single-stage & turret presses
-Sized to fit specific case heads & capture 0.125" of the case head for proper SAAMI head spacing

FEATURES
-.44 caliber
-Tapered to guide pilot into the case mouth
-Prevents case from wobbling when being trimmed to length
-For use with RCBS® Trim Pro® Case Trimmers, Rotary Case Trimmer-2 & Rotary Case Trimmer
-For use with RCBS Case Trimmers only

FEATURES
-Double Cavity Mold
-Produces a .451 diameter ball
-137.71 grains
-Includes handles

FEATURES
- Caliber: .300AAC Blackout
- Feature a Small Base Sizer Die designed for semi-automatic firearms, and a Taper Crimp Seater Die
-The Small Base Sizer guarantees the cartridge will rechamber in AR-platform weapons
- 2 dies/set

FEATURES
-Lee Pacesetter 2-Die Set
-25 Winchester Super Short Magnum (WSSM)
-Steel material
-Includes: Sizer Die and Bullet Seater Die with built in Roll Crimp
-Threads: 7/8"-14
-Accessories: Shellholder, Powder Dipper, Load Data Sheet, Plastic Container
-Adjustable crimp
-Built to last a lifetime and are great at producing factory like ammunition.

FEATURES
-.44 Magnum
-Incorporates a collet to apply a rifle type crimp to the case
-Makes these very difficult to crimp cartridges a delight to reload
-Bullets do not need a crimp groove, as the collet is so powerful it will form one

Note: This die is not carbine.

FEATURES
-Sturdy powder coated steel
-Places your press at the perfect counter stool or standing height
-Three-leg design assures absolute stability
-Rubber tipped legs
-Top is fitted with the patented, quick change Lee Bench Plate System
-Steel shelf with two bench plate receivers to store extra presses or mountable accessories
-Comes with one storage bin, which clips on the steel bin bracket provided with the stand
-Each leg had 8 mounting holes that allow you to customize your stand
-Includes drawing to customize & make your own extended work surface
-Dimensions: 39"H x 26"W x 24"D

FEATURES
-For .300 Winchester Short Magnum
-Case Length Gauge
-Precise, easy way to trim to length & square the case mouth
-Used with the Cutter & Lock Stud or Zip Trim

FEATURES
-20 Gauge
-Funnels the was through the crimp & into the wad chamber of the casing
-Fits all older MEC reloaders produced before 1983