Pearce Grips Inc.
![]()
FEATURES:
-Replaces the magazine base plate on the SIG P365
-Does not alter the capacity of the magazine
-Adds approximately 5/8" additional gripping surface as well as enhanced ergonomics
-The enhanced griping surface also incorporates a texture which closely matches the frame of the firearm
Other Features: Adds 5/8" additional length, fits sig p365, more grip length to factory 10 round magazine
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 1/4" of gripping surface
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
-They provide comfort without increasing the length of the grip over stock dimensions
Other Features: Fills the semi-circle at the lower area of the grip body for full metal lined magazines will not fit non-full metal lined magazines
FEATURES:
-Helps keep debris out of the back cavity
-Provides a clean finished look to the heel of the frame
Other Features: Fills in the cavity in the heel of the grip body utilizing a friction fit to secure it to the frame
FEATURES
-Grip Frame Insert for Glock 42 & 43
-Uses a friction fit for retention
-Helps keep debris out of the magazine well
FEATURES
-Grip Frame Insert for Glock 30S, 30SF, 29SF ( POST 2012 Frames)
-Installs in the bottom rear cavity of the frame utilizing the lanyard hole for retention
-Will only fit frames made after July 2012
Other Features: This product will only fit in post 2012 glock frames
FEATURES
-Fits fourth generation Glock 29 & 30
-Installs in the bottom rear cavity of the frame
-Utilizes the lanyard hole for retention
-Made for high impact polymer
-Designed to keep out dust and debris
-Allows for use with or without factory interchangeable backstraps
FEATURES
-Grip Frame Insert for Glock 20, 21 & 41
-Fits models 26, 27, 33, & 39
-Only fits the new Generation 4 frames
-Uses a friction fit for retention
-Allows for use of factory interchangeable backstraps
-Helps keep debris out of the magazine well
FEATURES
-Grip Frame Insert for Glock Model 20SF/21SF (Short Frames only)
-Will not fit a Generation 4 frame nor a standard Glock M20 or M21 frame
-Uses a friction fit for retention
-Helps keep debris out of the magazine well
Other Features: Fits short frame models only will not fit a standard glock g20 or g21 or gen4
FEATURES:
-Replaces the magazine base plate on the single stack 380 SHIELD EZ
-This extension does not alter the capacity of the magazine
-Adds approximately 1/2" additional gripping surface w/ enhanced ergonomics
Other Features: Replaces the magazine floor plate adding 1" in grip length to the factory magazine , adds 2 rounds to 9mm and 1 round to.40
Other Features: Replaces the magazine floor plate adding 1.5" in grip length to the factory magazine,
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Fits Taurus Slim PT709 & PT740
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 3/4" of additional length
-Slightly longer than the one provided by the factory and incorporates the factory texture pattern
as well as an ergonomic curve for better grip
Other Features: Adds 3/4" additional length, fits glock 43
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 3/4" of additional length
Other Features: Adds 3/4" additional length, fits glock 42
FEATURES
-Replace the magazine base plate & internal floor plate
-Adds three rounds to the Glock M26, two rounds to the Glock M27 & M33 & one round to the Glock M39
-Will add 1" additional length
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
-Forms the next logical finger positioning feature to provide control & comfort
Other Features: Adds three rounds to glock g26 adds two rounds to g27 and g33 adds one round to glock g39
FEATURES
-Grip extension for Beretta PG-380
-Replaces the magazine base plate & internal locking plate
-Does not alter the capacity of the magazine
-Adds approximately 1/2" additional length
-2 extensions per package
-Units blend with the contours & texture of the firearm
-Made from high impact polymer
Other Features: Fits beretta 3032 tomcat kel-tec p3at, and bersa 380
FEATURES
-Replace the magazine base plate & internal floor plate
-Adds two rounds to the Glock M26, one rounds to the Glock M27 & M33 & no rounds to the Glock M39
-Will add 5/8" additional length
-Fourth Generation Magazines only
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
-Forms the next logical finger positioning feature to provide control & comfort
Other Features: Fits generation 4 26/27/33, adds 2 rounds to 9mm, adds 1 round to 40s&w/.357sig
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
-They form the next logical finger positioning feature to provide control & comfort without sacrificing concealablility
FEATURES
-Rubber Wrap-Around Grips for Beretta Bobcat & Tomcat
-Provide a positive hold for the shooter
-Designed to fit either the Model 3032 Tomcat (1999 or earlier frames only) or the Model 21A Bobcat
-Not for use on Tomcat models equipped with an extended safety lever
Other Features: Fits models 21a and 3032 not for use with ext.Safety
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 1/2" of additional length
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
-They form the next logical finger positioning feature to provide control & comfort without sacrificing concealablility
FEATURES
-Grip extension for Glock 26/27/33/39
-Replaces the magazine base plate & internal floor plate
-Adds 2 rounds to the Glock 26 /1 round to the Glock 27 & 33 / 0 rounds to the Glock 39
-Adds 5/8" additional length
-Blends with the contours & texture of the handgun, giving a factory appearance
-Made from high impact polymer
Other Features: Increases 9mm by 2 rounds increases.40sw by 1 round
FEATURES
-Grip extension for Glock 26/27/33/39
-Replaces the magazine base plate
-Retains allother factory components
-Does not alter the capacity of the magazine
-Adds 1" additional length
-Blends with the contours & texture of the handgun, giving a factory appearance
-Made from high impact polymer
Other Features: Adds 1" additional length
FEATURES
-Grip extension for Glock 26/27/33/39 Gen 4
-Replaces the magazine base plate
-Retains allother factory components
-Does not alter the capacity of the magazine
-Adds 1" additional length
-Blends with the contours & texture of the handgun, giving a factory appearance
-Made from high impact polymer
Other Features: Adds 1" additional length, fits gen4 glock 26/27/33/39
FEATURES
-Grip extension for Glock 26/27/33/39
-Replaces the magazine base plate
-Retains allother factory components
-Does not alter the capacity of the magazine
-Adds 5/8" additional length
-Blends with the contours & texture of the handgun, giving a factory appearance
-Made from high impact polymer
Other Features: Adds 5/8" additional length
FEATURES:
-Replaces the magazine base plate on the GLOCK Gen 4 & 5
-Does not alter the capacity of the magazine
-Adds approximately 1/2" additional gripping surface as well as enhanced ergonomics
-The enhanced griping surface also incorporates a texture which closely matches the frame of the firearm
Other Features: This grip extension gives the user an additional 1/2" as well as included piece that can be installed to fill the semi-circular cut out in gen5
FEATURES
-Rubber Finger Groove Insert for Government Model 1911
-Fits under any GM 1911 side panel grip, adding rubber finger grooves for comfort & better handling
-Allows the user to use any type of side panel grips (wood, simulated ivory, pearlite, etc.) & have front
finger grooves
-Because the side portion of these grips are only 1mm thick, the overall width is only minimally affected
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 1/2" of additional length
-An optional filler piece is provided for Glock models with a semi-circular cut-out in the lower front
area of the grip body (which allows for installation of the PG-19 on all Mid & Full Size Glocks
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
Other Features: Not for use on non-full metal lined magazines
FEATURES
-Replace the magazine base plate & retain all other factory components.
-Adds approximately 1/2" of additional length
-Blends with the contours & texture of the handgun giving a factory appearance
-Made from High Impact Polymer & withstand drop tests at temperatures from -20F - 350F
FEATURES
-Replaces the magazine floor plate adding two rounds capacity to Glock factory
M20, M21, M29, M40 & M41 magazines
-Used on high capacity magazines only, it will not work on the 10-round M20 & M21 magazines
-Not for use on Glock M30 10-round magazines
-Works on 3rd & 4th Generations
-Works on Glock M30 9-round magazines, enabling the magazine to hold 11 rounds
-Made from High Impact Polymer & withstand temperatures from -20F to 350F
Other Features: For use on high cap mags only adds 2 rounds to capacity, this product will work on 9 round glock 30 magazines, not for use on model 30 10-round magazines
Other Features: Adds 3/4" additional length, fits s&w m&p shield plus 9mm & 40 s&w, does not add to mag capacity
FEATURES
-Grip extension for Springfield XDS Series (Compact only)
-Made from high impact polymer
-Withstands drop tests at temperatures from -20°F to 350°F
-Provides control & comfort without sacrificing concealability
Other Features: Fits xds compact only
FEATURES
-Replace the magazine floor plate & internal floor plate on the 9mm (13 round only), 40 S&W,
375 SIG & 45GAP
-Will add 1" in length & additional capacity
-Fits Glock 43
Other Features: Adds 1" in length adds additional capacity fits xd in 9mm (13rd only),.40sw,.357 sig, and.45 gap not compatible with xdm frames